Skip to Content

POLYBIT POLYINJECT STOP

Two component, fast setting polyurethane injection foam

  • Fast Setting
  • Crack Bridging

Features and benefits

Polyinject Stop is a two component, fast setting polyurethane injection foam to stop water leakage/flow from concrete and masonry structures.

Properties

Description

POLYBIT® POLYINJECT STOP is used as a fast water stop system, in cracks, crevices in construction above and below ground level. Typical applications are tunneling, basement, water tanks and water retaining structures. Available Pack : 11 Kg/Kit

Documents and downloads

How to use

How to use

Surface Preparation

If the water flow allows the surface should be stable and free of separating substances. Insufficiently firm layers and concrete slurry must be removed. Especially when applying surface packers and in case that the crack will be sealed, the substrate must be sufficiently prepared.

Work preparation

Polyinject Stop has to be applied with injection packers. The injection packers may be fixed into holes drilled directly into the crack or drilled diagonally from concrete adjacent to the crack or by the fixing of injection nipples bonded to the surface using Polyquick or Polyquick FS. For further assistance and instructions regarding the packer fixing and design please refer to our Method Statement. 

Injection

Polyinject Stop is a multi-component resin, which is injected into the water-carrying areas with pneumatic, electrical or hand-operated 1-component pumps. Take care to exclude moisture as much as possible and place the mixed material in an enclosed container after mixing. To decrease the potlife, up to 10% of catalyst can be added and mixed into Polyinject Stop. The mixture of Polyinject Stop and catalyst lasts approx. 8 hours. A skin can form on the liquid surface through reaction with water, which does not influence the processing of the material. Only mix sufficient resin that can be used within the pot life of the material. When flowing water has been stopped, reinject with Polyinject PU+ or any other suitable injection resin out of the Polyinject range to produce a permanent seal. For further information refer to the concerned datasheet permanent seal. For further information refer to the concerned datasheet 

Related articles

  • Bitustick Cool

    The Next Generation of Performed Bituminous Coatings 

  • Foundations and Flooring Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Wet Areas and Flooring Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Polycryl FR

    The Ultimate Fire Rated Coating Solution 

  • Polycryl PF

    Strong UV protection For Polyurethane Foam Roof  

  • Bituplus Ultra

    The Ultimate Torch On Membrane Range 

Related products

Related products

  • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/injections-special-liquids/product#/polybit-polyinject-rubber/SAP_0201WQP346X9/searchResult.productFields.MainImageAltText}
    POLYBIT POLYINJECT RUBBER
    For injection applications for extreme fine cracks which hardens to form a High quality rubber-like, flexible product. 
  • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/injections-special-liquids/product#/polybit-polyinject-ep/SAP_0201WQP34GJ5/searchResult.productFields.MainImageAltText}
    POLYBIT Polyinject EP
    2-component injection resin on epoxide basis with specific chemical and physical properties to seal and bond cracks of widths between 0.05 mm and 10 mm. Due to its low mixture viscosity 
  • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/injections-special-liquids/product#/polybit-polyinject-hose-pvc/SAP_0201WQP346X7/searchResult.productFields.MainImageAltText}
    POLYBIT POLYINJECT HOSE PVC
    Used to seal joints in concrete against water gress. 
Frequently asked questions

Frequently asked questions