Skip to Content

POLYBIT POLYINJECT HOSE PVC

PVC injection hose system

  • Excellent installation features
  • fast and easy to install

Features and benefits

Used to seal joints in concrete against water gress.

Properties

Description

POLYBIT® POLYINJECT Hose Can be used in all areas where construction joint are present and require sealing against water or require a particular joint sealing process.

Documents and downloads

How to use

How to use

Installation Procedures

1. Installation of Polyinject Hose PVC is preferably position in the middle of the substrate or if not possible, with a minimum of 100mm concrete cover from any outside edge.
2. The Polyinject Hose PVC must lie flat on the 1st concrete section with the hose clips at 150mm apart. If the concrete surface is rough, then the hose clip spacing need to be closer so the hose is touching the surface of the concrete.
3. The standard length of Polyinject Hose PVC, between injection points is approximately 10-12 meter. This will achieve the ultimate injection process.
4. At the injection point location where each individual hose length meets, an overlap of 150mm is required and with the two hoses laid parallel to each other at a distance of 30mm apart.
5. The injection points are to be installed in such a way as to allow access al all times.
6. Over length applications of up to 30 meters are possible but the correct installation procedures and use of Acrylic Gel injection material be used via a 2K Pump. Note: Please refer to the manufacturer’s installation procedures and guidelines (available upon request)

Simple injection Process

1. Check the continuation of the hose by flushing with water or with air.
2. The hose is injected via the injection point until traces of the injected material are discharged from the Vent end (opposite end of hose). This vent end is closed by means of an injection nipple as soon as the injected Material flows freely (without air pockets) from the vent.
3. The flow and extent of the inject ion material in the concrete joint s can be monitored during the injection Process by means of the inject ion pump’s pressure gauge if using a 2K pump.
4. The injection process is continued until constant pressure has been reached. Constant pressure indicates that the concrete joints are absorbing no more injection material and thus signaling the end of the process.
5. Any injection material still within the injection channel is simply flushed out by means of a water pump (2K pump Unit). Minimal pressure is required and it is simple and easy to achieve.
6. On completion of the flushing process, the injection channel is ready for future reinjections, if required 

Related articles

  • Bitustick Cool

    The Next Generation of Performed Bituminous Coatings 

  • Foundations and Flooring Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Wet Areas and Flooring Systems

    Discover, feel and touch our systems, through our mockup simulation boxes 

  • Polycryl FR

    The Ultimate Fire Rated Coating Solution 

  • Polycryl PF

    Strong UV protection For Polyurethane Foam Roof  

  • Bituplus Ultra

    The Ultimate Torch On Membrane Range 

Related products

Related products

  • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/injections-special-liquids/product#/polybit-polyinject-rubber/SAP_0201WQP346X9/searchResult.productFields.MainImageAltText}
    POLYBIT POLYINJECT RUBBER
    For injection applications for extreme fine cracks which hardens to form a High quality rubber-like, flexible product. 
  • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/injections-special-liquids/product#/polybit-polyinject-stop/SAP_0201WQP346Y0/searchResult.productFields.MainImageAltText}
    POLYBIT POLYINJECT STOP
    Polyinject Stop is a two component, fast setting polyurethane injection foam to stop water leakage/flow from concrete and masonry structures. 
  • ${/content/heliux/adhesive/polybit/com/en/products/waterproofing-solutions/injections-special-liquids/product#/polybit-polyinject-ep/SAP_0201WQP34GJ5/searchResult.productFields.MainImageAltText}
    POLYBIT Polyinject EP
    2-component injection resin on epoxide basis with specific chemical and physical properties to seal and bond cracks of widths between 0.05 mm and 10 mm. Due to its low mixture viscosity 
Frequently asked questions

Frequently asked questions